/var/keys/mg_cfg
===============================================
# EMM messages
# 00 don’t show any EMM’s (default)
# 01 show only valid EMM’s
# 02 show valid and bad EMM’s with complete data display
M: { 01 }
# ECM messages
# 00 don’t show any ECM’s
# 01 show only valid ECM’s (default)
# 02 show valid and bad ECM’s with complete data display
C: { 01 }
# AU
# 00 is ignored (default)
# 01 enable AU
# 02 AU Auto
A: { 02 }
# key update
# 01 update only new keys, default setting
# 02 update all keys (used for valid PMK checking)
U: { 01 }
# key files folder
# 00 keyfiles in /var/keys
# 01 keyfiles in /var/tmp
T: { 00 }
# network mode, use summ for several clients
# 00 no network (default)
# 01 newcamd netclient
# 02 radegast netclient
# 04 camd3 netclient
G: { 01 }
# network retry, use summ for several options
# 00 disable (default)
# 01 retry every new ecm
# 02 try to connect to offline shares every Q: seconds
# 04 try to detect and fast reconnect to lost (and not used atm) server
N: { 07 }
# network ecm timeout in seconds
K: { 10 }
# newcamd dead routes connect retry, sec
Q: { 600 }
# network shares priority
# 00 newcamd, radegast, camd3 (default)
# 01 camd3, radegast, newcamd
# 02 newcamd, camd3, radegast
P: { 00 }
# on screen display type
# 00 No OSD (default)
# 01 neutrino
# 02 enigma
O: { 00 }
# on screen display Options
# 03 default
# 01 show emu ecm
# 02 show network shares messages
# 04 show decoding failed / fta
# 08 show emm keys update
S: { 03 }
# Log options
# 00 Off (default)
# 01 Network
# 02 console
# 03 both
L: { 03 } 192.168.0.10 28007
# cache ecm pids and data used to open channels,
# store pids in /tmp/ca_cache.list at exit, load at startup,
# same syntax as restore.list
# 00 Off (default)
# 01 Ecm pids cache
# 02 Ecm data cache
# 03 both caches
H: { 00 }
# reread files on zap:
# 00 No (default)
# 01 config (including priority and ignore, but not replace/cache)
# 02 config and keys
# 03 both
R: { 00 }
# debug
# 00 off (default)
# 01 on
D: { 00 }
===============================================
В новых версиях mgcamd информация о «шаре» ищется в начале в файле /var/keys/newcamd.list. Если у тебя его нет — создай вручную. Синтаксис такой же, как и для newcamd.conf.
Например:
CWS_KEEPALIVE = yes
CWS_CONNECT_TIMEOUT = 20
CWS = 127.0.0.1 10001 local local 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan cardserv
===============================================
если используется старая версия mgcamd, в newcamd.conf включи опцию CWS_KEEPALIVE = yes (там по умолчанию = NO)
===============================================
Все должно работать